Showing posts with label Chicken Shak. Show all posts
Showing posts with label Chicken Shak. Show all posts

Sunday, July 1, 2012

Chicken Shak

Welcome back to The Shak.


I thought that while I was updating I would give you a little status report on the chickens. They are a long way from chikdom. In fact, one of the Delawares, white ones, has begun laying pullet eggs. None of the others have yet gotten into the act.


Since the chickens pretty much take care of themselves and spend the daylight hours outside acting all goofy, I do not have a lot to say. I'll let the pictures do that. They were taken on or about 10 June, in and around the monstrous lilac near the little barn. Enjoy.






Thanks for stopping. Come again soon.

Wednesday, April 11, 2012

Chicken Shak

Welcome back to The Shak.


I have been busy with other things since I built the chicken's nest boxes. Today, I got around to building roosts. It was an easy though somewhat time consuming process.
The coop before I began work on the roost.
After collecting some scrap lumber from the barns, I cut two pieces of wood for the rear, longer legs. These I cut to the height of the bottom of the nest boxes. This puts the highest roost just above the level of the lower nest box openings.


I cut two other pieces for the front, shorter legs. The length of each was half the piece of wood I cut. They amounted to just over 10" each. It was not important to me that they be any specific length.


Then I cut two pieces with the appropriate angles on each end to connect one longer leg and one smaller leg. These I screwed together with biscuits I cut from pieces of scrap 1" x 4" pine boards. This gave me the two end pieces I needed to connect the roosts across.
One of two end pieces. Roost poles will be nailed to these.
I recycled the poles I used for the roosts from the old chicken coop on the opposite end of the same building that houses the new coop and rabbit cages. This building is over one hundred and twenty five years old. A wall of horizontal logs divides the old coop from the current coop and rabbit area. The problem with the old coop is that one corner of the building is pulling apart. The work it would have taken to repair the building and use the old coop was prohibitive.
You can see where the stone foundation eroded and the building shifted. The logs are pulling apart at the corner and the front is buckling. I welcome suggestions about fixing this. As you can see, this picture was taken even before I began fixing the fence.
I laid the roosts across the ends I built, nailing them together 10" apart. It is rare that I use nails. In this case I made an exception.
Legs and roost poles in place. I think the chickens would have been outside in the courtyard had I not been tearing up their coop. They are inquisitive creatures.
Having a standing structure, I wrapped the outside vertical walls with 16ga. 2" x 4" wire. I only chose this because I had enough lying around to complete the job. From underneath, I stapled chicken wire to the roosts. This done, the chickens will not be able to access the area below the roosts by any means.


Because the chickens will be roosting there, their droppings will collect on the floor below the roosts. I do not want them playing in or eating poop. Can't blame a guy for that.


I used chicken wire under the roosts in case they would happen to lay eggs on the roost. This will keep the eggs from dropping through to the ground and breaking while allowing poop to drop to the floor.
No sooner finished than used. Yet another success!
After positioning the roost, which can be moved for cleaning, I removed all bedding from the coop, spread new bedding, re-positioned the feeder and waterer and rehung the heat lamp to a few feet off the lower end of the roost. At this point, the chickens are probably fine without the lamp, but there is a freeze warning tonight and with all the changes I made to their environment today, I did not want to stress them.
Done!
With that, I cleaned up my messes and headed for the shower. Then I ate the ice cream and strawberries I had so been looking forward to.


Thanks for stopping. Come again soon.

Monday, April 2, 2012

Chicken Shak

Welcome back to The Shak.


Are you ready for some fun? This may or may not do it for you. I enjoyed it. Now you can too.

I built nest boxes for the chickens. I knew how much space I had between the two posts that would contain them. With this piece of information, I walked to the machine shed. That is where I stacked the rough cut yet planed pine boards a friend offered me and I picked up on my last trip to the city.
It is good to have a friend who gave me this pile of boards
 Thank you friend!
You know who you are.
Not knowing exactly what I had received, I measured each of the forty-two pieces for length, width and thickness; however, I will not bore you with that process. The better half of the boards were 7/8" thick. Their widths and lengths varied greatly. Though none were 14" wide. Most of the sources I researched build 12" to 16" cubes with one open side.

14 goes into 70, 5 times. I had 70" between the posts. The thickness of the dividers and ends ate up some interior box space. Without going into fractions, my design gives each of ten boxes a width greater than 13" but less than 14". Their depth and height are 14".
These are the tools I used for this project. Somehow I forgot to include the rubber mallet. Gotta have a rubber mallet.
Armed with 7/8" thick lumber of varying widths and lengths, I began to build my jigsaw puzzle. I wanted the bottom and middle 20" wide. This took three separate boards each. The dividers had to be 14" high and measure 14" deep. This meant two boards for each of eight dividers. Two front sections require two boards each. The two ends are three boards each. The top is two boards. Two egg catchers meant two more boards. I think that is twenty-eight boards that needed to be cut.

I began by screwing the dividers to the bottom with 8 x 2 wood screws. This also served to hold the three bottom boards together. The dividers are cut, top and bottom at parallel eight degree angles. As you see the pictures of the boxes under construction on the work bench, they appear to lean in the direction of the open wall. When placed, the open wall will be plumb while the bottom and middle boards will slope downward toward the egg catcher.
Bottom boards with dividers installed.
Next, I added the front pieces. This significantly strengthened the structure. There is a 3" gap between the bottom of the bottom front board and the floor. This will allow eggs to pass into the egg catcher. Once in the egg catcher they stay clean and  can be easily collected without entering the coop. Because some chickens are egg eaters, this will also help prevent eggs being lost to the chickens. Once the egg rolls into the catcher, the chickens will not be able to get to them.
Front boards in place.
Now make another one just like it.
Two separate though relatively identical structures stacked one atop the other.
The middle board and its dividers are set atop the lower structure. I will not connect the middle boards to the lower dividers until installation. Each half will require two people to carry and must fit through two narrow doors in close proximity if it is to get from the garage work bench to the coop.
A different angle of the picture above.
This is taken from the open side.
After fastening the front boards to the top section, the end boards (which are screwed only to the bottom boards) and the top boards, it is starting to look like something.
Top and sides in place.
The picture above taken from the open side.
With the egg catchers in place, the real fun begins.
With the egg catchers in place, all bench work is done.
The boxes are ready for installation.

Remember, I did not connect the middle boards to the lower dividers. That was for ease of movement and installation and so I could take the two following photos.
The bottom half.

The top half.
Now to take all these pieces of wood and install them into the coop. There was some prep work to be done. And the entire job had to be done the day it began. Once I cut the hole in the coop, I would have to seal it before I quit for the day.

Below you see the wall and the two posts between which I installed the boxes. This is the way the coop has looked since I set it up.
The "before" shot of the wall that will become nest boxes.
Prep work complete.
You can see why I had to complete the job once begun.
After a limited struggle, some patience and a rubber mallet, the lower section is more-or-less where it will be for a long time to come.
The bottom in place.
From inside the coop looking out. It is not so crooked as it looks. My level indicates it is level. Must be operator error with regard to the camera.
With the bottom in place, the top slid into position with the assistance of that same rubber mallet. The wire mesh egg catcher cover is under construction. I did not have enough wire to make both covers of wire. I nailed a section of wire to the front boards on the lower section. Then, using j-clips and j-clip pliers, I hinged the wire cover over the egg catcher. For the top cover I used a couple hinges and a board.
Egg catcher covers under construction.
The bottom one is wire.
The top will be wood.
The finished product. I stapled the chicken wire down the front and filled any other gaps as necessary. The chickens are again safe from predators.
Done deal! This thing is not going anywhere.
From the inside looking out.
Well, there you have it. Ten nest boxes for clean, safe and easy to collect chicken eggs. These cannot be the end of it. Someday I will need more. That is enough for one day.


My next chicken related project will be to add roosts to the open side of the boxes and elsewhere in the coop. That is for another post.


Thanks for stopping. Come again soon.

Thursday, March 29, 2012

Chicken Shak

Welcome back to The Shak.

I performed the last upgrade to the chickens food and water situation. The little buggers are not so little anymore. They seem to grow noticably day-to-day. The only problem with all this growing is their knocking over their feeders and waterers. Solution? Bigger stuff.
40# feeder on the left.
7 gallon waterer to the right.
I purchased a new seven gallon waterer and a new forty pound capacity feeder. These are both suspended from the ceiling. Not only will this keep the chickens from toppling their food and water, it will and has reduced my work load. There is not much left for me to do but clean the removable water tray. It snaps off and on without my having to take down the feeder. And with their large capacities, I rarely have to fill them. Suspending them keeps them at the right height (chicken back height); thereby, preventing the chickens from scratching the food out of the feeder and crapping in or spilling the water.
Chicks no more.
 I also bought egg layer crumble instead of chick feed. They grow up so fast.
Look at the size of the breasts on that chicken!

Thanks for stopping. Come again soon.

Saturday, March 17, 2012

Chicken Shak

Welcome back to The Shak.


In the last episode, you were witness to a past which ended twelve days ago. Today's episode features the present as it drifts into the past. Let me begin by saying... chicks grow quickly. It all begins innocently enough. First, one does it, then they all start doing it. They roost atop the Ball jar feeders. Which in itself is amusing; however, another hop would land them outside the brooder. And since I assume being cut off from all food, water, heat and companionship through dumb curiosity, with not so much as a predator to set me free, would suck, I began to think about it.
The coop has been ready since November or December. When I set up the brooder, I did so in the best shielded corner of the coop. The coop is sealed. Nothing larger than a chicken wire hexagon enters or leaves without my consent. So, my main concern with a chick getting out was not predators. Nor was it food and water. It wouldn't starve or dehydrate before I had found it. The one real concern is heat. Both that of the heat lamp and that of other chickens.
I was in the barn Thursday morning investigating the nest of the doe who had delivered 13 kits overnight, when I saw one of the Buff Orpington chicks bound like Bruce Lee off the dome of the heat lamp and land on the cardboard brooder cover. She seemed all too happy to see me; jumping into my hand only seconds after landing. Otherwise she had not moved. She chirped a few times.
After a trip to Fleet Farm for bedding, feed, fence boards and gate building materials, I spread the bedding throughout the coop. After removing the cardboard brooder from the coop completely, I used paving stones as platforms upon which to place feeders and waterers. Waterers stay much cleaner now that they are not on the bedding. Much less work for me. The heat lamp hangs in its original place.
Three days and two nights in their new digs, they all seem very happy.

Chicken Shak

The following was pulled from facebook posts. I put it all together for you here. I see it as an archive, a prequel to what has come since. The pictures of mature hens are for illustration only. Though the chicks are of the varieties pictured, results may vary. They are growing quickly. Due to that, their living arrangements have changed for the bigger since these pictures were taken. This blog ends with them at twelve days. They are twenty days old at this writing. Enjoy the pictures. Come back soon. Plenty more to catch you up on.
The brooder
This is the brooder I built for the soon to arrive chicks (ship 02/27/12). After spending the better part of the day looking for cardboard on a roll and not finding it, I settled for this much superior design. I repurposed the rabbit cage shipping boxes. I rounderd off the corners with flooring boxes someone left straddling a too narrow surface in the garage. This left them, to my great satisfaction, the perfect arc for my needs. This is very important as chicks will pile one upon the other in corners; thereby, increasing their mortality rate. That is no way to treat chicks.
The brooder from the outside

Here you see the brooder from the outside. To the left are the remnants of the bag of pine shavings I used as litter. I put the brooder in the chicken coop. That way the chicks wont have too great an adjustment when hardy enough to roam. The next five pictures are of the five breeds of chickens I ordered. I ordered 6 chicks of each breed. All pullets. No cocks. I can take care of that when the time comes.